ExtraHop Trace REST API Guide

Introduction to the ExtraHop REST API

The ExtraHop REST API enables you to automate administration and configuration tasks on your ExtraHop system. You can send requests to the ExtraHop API through a Representational State Transfer (REST) interface, which is accessed through resource URIs and standard HTTP methods.

When a REST API request is sent over HTTPS to an ExtraHop system, that request is authenticated and then authorized through an API key. After authentication, the request is submitted to the ExtraHop system and the operation completes.
Video:See the related training: Rest API Overview

Each ExtraHop system provides access to the built-in ExtraHop REST API Explorer, which enables you to view all of the available system resources, methods, properties, and parameters. The REST API Explorer also enables you to send API calls directly to your ExtraHop system.

Note:This guide is intended for an audience that has a basic familiarity with software development and the ExtraHop system.

ExtraHop API requirements

Before you can begin writing scripts for the ExtraHop REST API or performing operations through the REST API Explorer, you must meet the following requirements:

Access and authenticate to the ExtraHop REST API

Setup users and users with system and access administration privileges control whether users can generate API keys. For example, you can prevent remote users from generating keys or you can disable API key generation entirely. When this functionality is enabled, API keys are generated by users and can be viewed only by the user who generated the key.

Note:Administrators set up user accounts and assign privileges, but then users generate their own API keys. Users can delete API keys for their own account, and users with system and access administration privileges can delete API keys for any user. For more information, see Users and user groups.

After you generate an API key, you must append the key to your request headers. The following example shows a request that retrieves metadata about the firmware running on the ExtraHop system:

curl -i -X GET --header "Accept: application/json" \
--header "Authorization: ExtraHop apikey=2bc07e55971d4c9a88d0bb4d29ecbb29" \
"https://<hostname-or-IP-of-your-ExtraHop-system>/api/v1/extrahop"

Privilege levels

User privilege levels determine which ExtraHop system and administration tasks the user can perform through the ExtraHop REST API.

You can view the privilege levels for users through the granted_roles and effective_roles properties. The granted_roles property shows you which privilege levels are explicitly granted to the user. The effective_roles property shows you all privilege levels for a user, including those received outside of the granted role, such as through a user group.

The granted_roles and effective_roles properties are returned by the following operations:

  • GET /users
  • GET /users/{username}

The granted_roles and effective_roles properties support the following privilege levels. Note that the type of tasks for each ExtraHop system vary by the available resources listed in the REST API Explorer and depend on the modules enabled on the system and user module access privileges.

Privilege level Actions allowed
"system": "full"
  • Enable or disable API key generation for the ExtraHop system.
  • Generate an API key.
  • View the last four digits and description for any API key on the system.
  • Delete API keys for any user.
  • View and edit cross-origin resource sharing.
  • Perform any administration task available through the REST API.
  • Perform any ExtraHop system task available through the REST API.
"write": "full"
  • Generate your own API key.
  • View or delete your own API key.
  • Change your own password, but you cannot perform any other administration tasks through the REST API.
  • Perform any ExtraHop system task available through the REST API.
"write": "limited"
  • Generate an API key.
  • View or delete their own API key.
  • Change your own password, but you cannot perform any other administration tasks through the REST API.
  • Perform all GET operations through the REST API.
  • Perform metric and record queries.
"write": "personal"
  • Generate an API key.
  • View or delete your own API key.
  • Change your own password, but you cannot perform any other administration tasks through the REST API.
  • Perform all GET operations through the REST API.
  • Perform metric and record queries.
"metrics": "full"
  • Generate an API key.
  • View or delete your own API key.
  • Change your own password, but you cannot perform any other administration tasks through the REST API.
  • Perform metric and record queries.
"metrics": "restricted"
  • Generate an API key.
  • View or delete your own API key.
  • Change your own password, but you cannot perform any other administration tasks through the REST API.
"ndr": "full"
  • View security detections
  • View and create investigations

This is a module access privilege that can be granted to a user in addition to one of the following system access privilege levels:

  • "write": "full"
  • "write": "limited"
  • "write": "personal"
  • "write": null
  • "metrics": "full"
  • "metrics": "restricted"
"ndr": "none"
  • No access to NDR module content

This is a module access privilege that can be granted to a user in addition to one of the following system access privilege levels:

  • "write": "full"
  • "write": "limited"
  • "write": "personal"
  • "write": null
  • "metrics": "full"
  • "metrics": "restricted"
"npm": "full"
  • View performance detections
  • View and create dashboards
  • View and create alerts

This is a module access privilege that can be granted to a user in addition to one of the following system access privilege levels:

  • "write": "full"
  • "write": "limited"
  • "write": "personal"
  • "write": null
  • "metrics": "full"
  • "metrics": "restricted"
"npm": "none"
  • No access to NPM module content

This is a module access privilege that can be granted to a user in addition to one of the following system access privilege levels:

  • "write": "full"
  • "write": "limited"
  • "write": "personal"
  • "write": null
  • "metrics": "full"
  • "metrics": "restricted"
"packets": "full"
  • View and download packets through the GET /packets/search and POST /packets/search operations.

This is an add-on privilege that can be granted to a user with one of the following privilege levels:

  • "write": "full"
  • "write": "limited"
  • "write": "personal"
  • "write": null
  • "metrics": "full"
  • "metrics": "restricted"
"packets": "full_with_keys"
  • View and download packets and session keys through the GET /packets/search and POST /packets/search operations.

This is an add-on privilege that can be granted to a user with one of the following privilege levels:

  • "write": "full"
  • "write": "limited"
  • "write": "personal"
  • "write": null
  • "metrics": "full"
  • "metrics": "restricted"
"packets": "slices_only"
  • View and download the first 64 bytes of packets through the GET /packets/search and POST /packets/search operations.

This is an add-on privilege that can be granted to a user with one of the following privilege levels:

  • "write": "full"
  • "write": "limited"
  • "write": "personal"
  • "write": null
  • "metrics": "full"
  • "metrics": "restricted"

Manage API key access

Users with system and access administration privileges can configure whether users can generate API keys for the ExtraHop system. You can allow only local users to generate keys, or you can also disable API key generation entirely.

Users must generate an API key before they can perform operations through the ExtraHop REST API. Keys can be viewed only by the user who generated the key or system administrators with unlimited privileges. After a user generates an API key, they must append the key to their request headers.
  1. Log in to the Administration settings on the ExtraHop system through https://<extrahop-hostname-or-IP-address>/admin.
  2. In the Access Settings section, click API Access.
  3. In the Manage API Access section, select one of the following options:
    • Allow all users to generate an API key: Local and remote users can generate API keys.
    • Only local users can generate an API key: Remote users cannot generate API keys.
    • No users can generate an API key: No API keys can be generated by any user.
  4. Click Save Settings.

Generate an API key

You must generate an API key before you can perform operations through the ExtraHop REST API. Keys can be viewed only by the user who generated the key or by users with system and access administration privileges. After you generate an API key, add the key to your request headers or the ExtraHop REST API Explorer.

Before you begin

Make sure the ExtraHop system is configured to allow API key generation.
  1. In the Access Settings section, click API Access.
  2. In the Generate an API Key section, type a description for the new key, and then click Generate.
  3. Scroll down to the API Keys section, and copy the API key that matches your description.
You can paste the key into the REST API Explorer or append the key to a request header.

Configure cross-origin resource sharing (CORS)

Cross-origin resource sharing (CORS) allows you to access the ExtraHop REST API across domain-boundaries and from specified web pages without requiring the request to travel through a proxy server.

You can configure one or more allowed origins or you can allow access to the ExtraHop REST API from any origin. Only users with system and access administration privileges can view and edit CORS settings.
  1. In the Access Settings section, click API Access.
  2. In the CORS Settings section, specify one of the following access configurations.
    • To add a specific URL, type an origin URL in the text box, and then click the plus (+) icon or press ENTER.

      The URL must include a scheme, such as HTTP or HTTPS, and the exact domain name. You cannot append a path; however, you can provide a port number.

    • To allow access from any URL, select the Allow API requests from any Origin checkbox.
      Note:Allowing REST API access from any origin is less secure than providing a list of explicit origins.
  3. Click Save Settings and then click Done.

Learn about the REST API Explorer

The REST API Explorer is a web-based tool that enables you to view detailed information about the ExtraHop REST API resources, methods, parameters, properties, and error codes. Code samples are available in Python, cURL, and Ruby for each resource. You also can perform operations directly through the tool.

Open the REST API Explorer

You can open the REST API Explorer from the Administration settings or through the following URL:

https://<extrahop-hostname-or-ip-address>/api/v1/explore/
  1. Log in to the Administration settings on the ExtraHop system through https://<extrahop-hostname-or-IP-address>/admin.
  2. From the Access Setting section, click API Access.
  3. On the API Access page, click REST API Explorer.
    The REST API Explorer opens in your browser.

View operation information

From the REST API Explorer, you can click any operation to view configuration information for the resource.

The following table provides information about the sections available for resources in the REST API Explorer. Section availability varies by HTTP method. Not all methods have all of the sections listed in the table.

Section Description
Body Parameters Provides all of the fields for the request body and supported values for each field.
Parameters Provides information about the available query parameters.
Responses Provides information about the possible HTTP status codes for the resource. If you click Send Request, this section also includes the response from the server and the cURL, Python, and Ruby syntax required to send the specified request.
Tip:Click Model to view descriptions of the fields returned in a response.

Identify objects on the ExtraHop system

Objects on the ExtraHop system can be identified by any unique value, such as the IP address, MAC address, name, or system ID. However, to perform API operations on a specific object, you must locate the object ID. You can easily locate the object ID through the following methods in the REST API Explorer.

  • The object ID is provided in the headers returned from a POST request. For example, if you send a POST request to create a page, the response headers display a location URL.

    The following request returned the location for the newly created tag as /api/v1/tags/1 and the ID for the tag as 1.

    {
     "date": "Tue, 09 Nov 2021 18:21:00 GMT ",
     "via": "1.1 localhost",
     "server": "Apache",
     "content-type": "text/plain; charset=utf-8",
     "location": "/api/v1/tags/1",
     "cache-control": "private, max-age=0",
     "connection": "Keep-Alive",
     "keep-alive": "timeout=90, max=100",
     "content-length": "0"
    }
  • The object ID is provided for all objects returned from a GET request. For example, if you perform a GET request on all devices, the response body contains information for each device, including the ID.

    The following response body displays an entry for a single device, with an ID of 10212:

    {
     "mod_time": 1448474346504,
     "node_id": null,
     "id": 10212,
     "extrahop_id": "test0001",
     "description": null,
     "user_mod_time": 1448474253809,
     "discover_time": 1448474250000,
     "vlanid": 0,
     "parent_id": 9352,
     "macaddr": "00:05:G3:FF:FC:28",
     "vendor": "Cisco",
     "is_l3": true,
     "ipaddr4": "10.10.10.5",
     "ipaddr6": null,
     "device_class": "node",
     "default_name": "Cisco5",
     "custom_name": null,
     "cdp_name": "",
     "dhcp_name": "",
     "netbios_name": "",
     "dns_name": "",
     "custom_type": "",
     "analysis_level": 1
    },
  • The object ID is provided in the URL for most objects. For example, in the ExtraHop system, click on Assets, and then Devices. Select any device and view the URL. In the following example, the URL for the device page shows Oid=10180.
    https://10.10.10.205/extrahop/#/Devices?details=true&device
    Oid=10180&from=6&interval_type=HR&until=0&view=l2stats

    To perform specific requests for that device, add 10180 to the id field in the REST API Explorer or to the body parameter in your request.

    The URL for dashboards displays a short_code, which appears after /Dashboard. When you add the short_code to the REST API Explorer or to your request, you must prepend a tilde to the short code.

    In the following example, kmC9Y is the short_code. To perform requests for this dashboard, add ~kmC9Y as the value for the short_code field.

    https://10.10.10.205/extrahop/#/Dashboard/kmC9Y/?from=6&interval_
    type=HR&until=0

    You can also find the short_code and dashboard ID in the Dashboard Properties for any dashboard, which can be accessed from the command menu . Some API operations, such as DELETE, require the dashboard ID.

ExtraHop API resources

You can perform operations on the following resources through the ExtraHop REST API. You also can view more detailed information about these resources, such as available HTTP methods, query parameters, and object properties in the REST API Explorer.

APIKey

An API key enables a user to perform operations through the ExtraHop REST API.

You can generate the initial API key for the setup user account through the REST API. All other API keys are generated through the API Access page in the Administration settings.

The following table displays all of the operations you can perform on this resource:

Operation Description
GET /apikeys Retrieve all API keys.
POST /apikeys Create the initial API key for the setup user account.
GET /apikeys/{keyid} Retrieve information about a specific API key.

Appliance

The ExtraHop system consists of a network of connected ExtraHop appliances, such as sensors, consoles, recordstores, and packetstores that perform tasks such as monitoring traffic, analyzing data, storing data, and identifying detections.

You can retrieve information and establish connections for local and remote ExtraHop appliances.

Note:You can only establish a connection between similar ExtraHop appliances, such as Reveal(x) Enterprise or Performance.

The following table displays all of the operations you can perform on this resource:

Operation Description
GET /appliances Retrieve all remote ExtraHop appliances connected to the local appliance.
POST /appliances Establish a new connection to a remote ExtraHop appliance.
DELETE /appliances/{id} Disconnect a specific ExtraHop appliance from this console.
GET /appliances/{id} Retrieve a specific remote ExtraHop appliance connected to the local appliance (only valid on consoles).
GET /appliances/{id}/cloudservices Retrieve the status of ExtraHop Cloud Services on this appliance (only valid on consoles).
GET /appliances/{id}/productkey Retrieve the product key for a specified appliance (only valid on consoles).
GET /appliances/{ids_id}/association Retrieve the ID of the packet sensor that the IDS sensor is joined to.
POST /appliances/{ids_id}/association Join an IDS sensor to a packet sensor.
GET /appliances/firmware/next Retrieve firmware versions that remote ExtraHop systems can be upgraded to (only valid on consoles).
POST /appliances/firmware/upgrade Upgrade firmware on remote ExtraHop systems connected to the local system. Firmware images are downloaded from ExtraHop Cloud Services (only valid on consoles).
GET /appliances/{ids_id}/association Retrieve the ID of the packet sensor that the IDS sensor is joined to (only valid on consoles).
POST /appliances​/{ids_id}​/association Join an IDS sensor to a packet sensor (only valid on consoles).

ExtraHop

This resource provides metadata about the ExtraHop system.

The following table displays all of the operations you can perform on this resource:

Operation Description
GET /extrahop Retrieve metadata about the firmware running on the ExtraHop system.
GET /extrahop/edition Retrieve the edition of the ExtraHop system.
POST /extrahop/firmware Upload a new firmware image to the ExtraHop system. For more information, see Upgrade ExtraHop firmware through the REST API.
POST ​/extrahop​/firmware​/download​/url Download a new firmware image onto the ExtraHop system from a URL.
POST /extrahop/firmware/latest/upgrade Upgrade the ExtraHop system to the most recently uploaded firmware image.
GET /extrahop/idrac Retrieve the iDRAC IP address of the ExtraHop system.
GET /extrahop/platform Retrieve the platform name of the ExtraHop system.
GET /extrahop/processes Retrieve a list of processes running on the ExtraHop system.
POST /extrahop/processes/{process}/restart Restart a process running on the ExtraHop system.
GET /extrahop/services Retrieve settings for all services.
PATCH /extrahop/services Update the settings for services.
POST /extrahop/restart Restart the ExtraHop system.
POST /extrahop/sslcert Regenerate the SSL certificate on the ExtraHop system. For more information, see Create a trusted SSL certificate through the REST API
PUT /extrahop/sslcert Replace the SSL certificate on the ExtraHop system.
POST /extrahop/sslcert/signingrequest Create an SSL certificate signing request. For more information, see Create a trusted SSL certificate through the REST API.
GET /extrahop/ticketing Retrieve the ticketing integration status.
PATCH /extrahop/ticketing Enable or disable ticketing integration.
GET /extrahop/version Retrieve the version of the firmware running on the ExtraHop system.

Implementation information and instructions for each operation are documented in the REST API Explorer. You can click on any operation in the REST API Explorer to view implementation information such as parameters, response class and messages, and JSON model and schema.

Jobs

You can monitor the progress of some administration jobs started through the REST API. If a REST request creates a job, the job ID is returned in the location header of the response. The following operations create jobs:

  • POST ​/extrahop​/firmware​/latest​/upgrade
  • POST ​/extrahop​/sslcert

The following table displays all of the operations you can perform on this resource:

Operation Description
GET /jobs Retrieve the status of all jobs.
GET /jobs/{id} Retrieve the status of a specific job.

License

This resource enables you to retrieve and set product keys or to retrieve and set a license.

The following table displays all of the operations you can perform on this resource:

Operation Description
GET /license Retrieve the license applied to this ExtraHop system.
PUT /license Apply and register a new license to the ExtraHop system.
GET /license/productkey Retrieve the product key to this ExtraHop system.
PUT /license/productkey Apply the specified product key to the ExtraHop system and register the license.

Running config

The running configuration file is a JSON document that contains core system configuration information for the ExtraHop system.

The following table displays all of the operations you can perform on this resource:

Operation Description
GET /runningconfig Retrieve the current running configuration file.
PUT /runningconfig Replace the current running configuration file. Configuration file changes are not automatically saved.
POST /runningconfig/save Save the current changes to the running configuration file.
GET /runningconfig/saved Retrieve the saved running configuration file.

Support pack

A support pack is a file that contains configuration adjustments provided by ExtraHop Support.

The following table displays all of the operations you can perform on this resource:

Operation Description
GET /supportpacks Retrieve metadata about all support packs.
POST /supportpacks Upload and run a support pack.
POST /supportpacks/execute Run a new support pack.
GET /supportpacks/queue/{id} Check on the status of an in-progress, running support pack.
GET /supportpacks/{filename} Downlolad an existing support pack by filename.

User

The user resource enables you to create and manage the list of users who have access to the ExtraHop system and the privilege levels for those users.

The following table displays all of the operations you can perform on this resource:

Operation Description
GET /users Retrieve all users.
POST /users Create a new user.
DELETE /users/{username} Delete a specific user.
GET /users/{username} Retrieve a specific user.
PATCH /users/{username} Update settings for a specific user.
GET /users/{username}/apikeys Retrieve all API keys for a specific user.
GET /users/{username}/apikeys/{keyid} Retrieve information about a specific API key and user.

ExtraHop REST API examples

Upgrade ExtraHop firmware through the REST API

You can automate upgrades to the firmware on your ExtraHop appliances through the ExtraHop REST API. This guide provides instructions to upgrade through the REST API Explorer, a cURL command, and a Python script.

Note:If your appliance is connected to ExtraHop Cloud Services, you can simplify the upgrade process by viewing available firmware versions and downloading firmware directly to the system from ExtraHop Cloud Services. For more information, see Upgrade ExtraHop firmware through the REST API with ExtraHop Cloud Services.

While the firmware upgrade process is similar across all ExtraHop appliances, some appliances have additional considerations or steps that you must address before you install the firmware in your environment. If you need assistance with your upgrade, contact ExtraHop Support.

All appliances must meet the following requirements:

  • The firmware version must be compatible with your appliance model.
  • The firmware version on your appliance must be supported by the upgrade version.
  • Command appliances must be running firmware that is greater than or equal to their connected appliances.
  • Discover appliances must be running firmware that is greater than or equal to connected Explore and Trace appliances.

If your deployment only includes a sensor, proceed to the API Explorer, cURL or Python upgrade instructions.

If your deployment includes additional appliance types, you must address the following dependencies before proceeding with the upgrade instructions.

If your deployment includes... Pre-upgrade tasks Upgrade order
Command appliances Reserve a maintenance window of an hour for Command appliances managing 50,000 devices or more.
  • Command appliance
  • Discover appliances
  • All Explore appliances (manager nodes, then data nodes)
  • Trace appliances
Explore appliances See Upgrading ExtraHop recordstores.
Trace appliances None

Upgrade ExtraHop firmware through the REST API Explorer

Download firmware and upgrade the appliance
  1. Click POST /extrahop/firmware/download/url.
  2. Click Try it out.
  3. In the body field, specify the following fields:

    firmware_url: The URL that the firmware .tar file can be downloaded from.

    upgrade: Indicates whether to upgrade the appliance after the firmware download completes. Set this field to true.

    The body field should look similar to the following example text:

    {
      "upgrade": true,
      "firmware_url": "https://example.extrahop.com/eda/8.7.1.tar"
    }

  4. Click Send Request.
    In the Response headers, note the value after the last forward slash in the location header. You will need this value to monitor the progress of the upgrade job. For example, the job ID in the following example is ebbdbc9e-7113-448c-ab9b-cc0ec2307702
    /api/v1/jobs/ebbdbc9e-7113-448c-ab9b-cc0ec2307702
Monitor the progress of the upgrade job
  1. Click Jobs.
  2. Click GET /jobs/{id}.
  3. In the id field, type the value you copied from the location header in the previous task.
  4. Click Send Request.
  5. In the Response body, view information about the job.
    The status field is DONE when the job is complete.

Upgrade ExtraHop firmware with cURL

You can upgrade the firmware on an appliance through the cURL command.

Before you begin

  • The cURL tool must be installed on your machine.
  • The system firmware .tar file must be downloaded on your machine.
  1. Open a terminal application.
  2. Download firmware and upgrade the appliance.

    Run the following command, where YOUR_KEY is the API key for your user account, HOSTNAME is the hostname of your ExtraHop appliance, and FIRMWARE_URL is the URL that the firmware .tar file can be downloaded from:

    curl -v -X POST https://HOSTNAME/api/v1/extrahop/firmware/download/url -H "Authorization: ExtraHop apikey=YOUR_KEY" -H "Content-Type: application/json" -d "{ \"upgrade\": true, \"firmware_url\": \"FIRMWARE_URL\"}"

    In the command output, note the job ID in the Location header. For example, the job ID in the following example is ebbdbc9e-7113-448c-ab9b-cc0ec2307702:

    < Location: /api/v1/jobs/ebbdbc9e-7113-448c-ab9b-cc0ec2307702
  3. Monitor the progress of the upgrade job.
    Run the following command, where YOUR_KEY is the API key for your user account HOSTNAME is the hostname of your appliance, and JOB_ID is the ID you recorded in the previous step:
    curl -v -X GET https://HOSTNAME/api/v1/jobs/JOB_ID -H "Authorization: ExtraHop apikey=API_KEY"

    The command displays an object that contains information about the upgrade job. The upgrade is complete when the status field is DONE. If the upgrade is not complete, wait a few minutes and run the command again.

Retrieve and run the example Python script

The ExtraHop GitHub repository contains an example Python script that upgrades multiple appliances by reading URLs, API keys, and firmware file paths from a CSV file.

Important:The example python script authenticates to the sensor or console through an API key, which is not compatible with the Reveal(x) 360 REST API. To run this script with Reveal(x) 360, you must modify the script to authenticate with API tokens. See the py_rx360_auth.py script in the ExtraHop GitHub repository for an example of how to authenticate with API tokens.
Note:The script does not automatically disable record ingest for ExtraHop recordstores. You must manually disable record ingest before running the script for an ExtraHop recordstores.
  1. Go to the ExtraHop code-examples GitHub repository and download the contents of the upgrade_system directory to your local machine.
  2. In a text editor, open the systems.csv file and replace the example values with the hostnames and API keys of your appliances.
  3. Run the upgrade_system_url.py script.
    The following arguments are optional:
    --max-threads {int}
    Specifies the maximum number of concurrent threads. The default value is 2.
    --wait {float}
    Specifies the number of minutes to wait before checking the progress of an upgrade job. The default value is 0.5.

    For example, the following command upgrades a maximum of 3 appliances at a time:

    python3 upgrade_system_url.py --max-threads 3
    Note:If the script returns an error message that the SSL certificate verification failed, make sure that a trusted certificate has been added to your sensor or console. Alternatively, you can add the verify=False option to bypass certificate verification. However, this method is not secure and not recommended. The following code sends an HTTP GET request without certificate verification:
    requests.get(url, headers=headers, verify=False)

Upgrading ExtraHop recordstores

Pre-upgrade tasks

Before upgrading an ExtraHop recordstore, you must halt record ingest. You can halt record ingest for all of the nodes in a cluster from a single node.

Note:The message Could not determine ingest status on some nodes and Error might appear on the Cluster Data Management page in the Administration settings of the upgraded nodes until all nodes in the cluster are upgraded. These errors are expected and can be ignored.
  1. Open a terminal application.
  2. Run the following command, where YOUR_KEY is the API for your user account, and HOSTNAME is the hostname of your ExtraHop recordstore:
    curl -X PATCH "https://HOST/api/v1/extrahop/cluster" -H "accept: application/json" -H "Authorization: ExtraHop apikey=YOUR_KEY" -H "Content-Type: application/json" -d "{ \"ingest_enabled\": false}"
Post-upgrade tasks

After you have upgraded all of the nodes in the recordstore cluster, enable record ingest.

  1. Open a terminal application.
  2. Run the following command, where YOUR_KEY is the API for your user account, and HOSTNAME is the hostname of your ExtraHop recordstore:
    curl -X PATCH "https://HOST/api/v1/extrahop/cluster" -H "accept: application/json" -H "Authorization: ExtraHop apikey=YOUR_KEY" -H "Content-Type: application/json" -d "{ \"ingest_enabled\": true}"
Last modified 2024-04-02